Sardone v1 Jet build with testbed - Poor Max static thrust 12Kg - Would you help?

Are you sure that your calculations are right?
Over the thumb I would say your thrust is a bit less than twice the scale reading + ca. the weight of the rocket (I didnt run the numbers, but your string splits the force to 2 fixations of the string (like a pulley) and your scale measures only one side, but I has to be less than x2 since your string is not vertical and so you got a horizontal part inside your scale readings (should be about x sin(angle of string)).

So you would actually be closer to 20-25kg thrust…

And you might have gotten @Mat wrong :wink:

Dont give up, whoever said its a dead end. There are way more combinations with jet rather than prop only. Way harder task than prop setup if u ask me, but not a dead end!

You may need a more water to see it full potentiel as well :wink:

So you have more than 20.000 rpm - maybe that kill your prop :sunglasses:
Did you measure rpm outside and inside water?

Since the input current when running in air changed dramatically before and after the in water test, I assume either your setup wasn’t waterproof or your motor is damaged due to overheating.

Also your freerunning rpm with 50V 360kV would be 18,000. Thus you would reach the maximum output power at 9,000 rpm, which is probably not enough to create sufficient thrust. So yes, the first thing you should do is measure the max rpm when submerged.

I think it’s more because of 16S

I assume your pitch per full revolution is 44 mm, not 11, right? If you want to accelerate the water to 30 km/h or 500m/minute, you’ll need more than 50krpm at 11 mm pitch or about 15krpm at 44 mm.

2 Likes

Congratulations for what you have reached so far. As said earlier, your way of using the luggage scale might need some tuning (coefficient). A static pull or push inline with the scale provides best possible results. Therefore, may I suggest a method adapted from @Frage and his bathroom scale method ?
You could make a hole in a board to the size of the scale display.
The bathroom scale being pressed between this white board and the water jet tube…
CON: the wires will be submerged

As @Giga said, in response to @Dynamik , I think that @Mat meant “I would like to get stuck in that kind of dead end any day” regarding the quality of the esurf.com impeller - A beast: 20.5kw = 50V x 410 A :wink:

Okay, according to your number (13cm height and 23cm diag), angle between rope and platform is ~48.5deg.
Formular so your thrust in KG is then: F(thrust) = (2 * F(scale in KG) * sinD(48.5)) + Weight(whole rocket in KG) - Volume(submerged Rocket while test in L).

2 * sinD(48.5) is a factor of ~1,5 so if you look at your numbers at e.g. 40A you have to have at least more than 14kg thrust, probably a lot more (assuming the rocket is not lighter than water).

With this method, you have the precision without the swimming pool :upside_down_face:
You can either screw the board to the bin or stand on it to avoid a take off :wink:

1 Like

@Giga is right (I see my angle as 34.4D though) and probably how I put the scale create some reading complication.

The way I calculate it is based on the below:

l * Sin(a )= h, Sin(a) = h / l = 0.565 then h = l * 0.565 (same proportion of the force component)

What you read in the scale is W1, (the red force on the right), but to keep Sardone in place you also use W2 which is the same as W1.

Then you have the Sardone weight (S) that has to be measured when Sardone is partially submerged as it is in the test. S = 1.4Kg

So Thrust T = 2 * W1 * 0.565 + 1.4 (all in Kg)

That’s where the numbers come from.
Thank you @SoEFoil, your solution is Super Clever, but for my case, at this point, it is easiest to fix the formula if it is wrong.
By the way, the trick I secured the cover is this:
image
With a Ring of sealant to avoid showers.

A bathroom scale price starts as low as 10USD / EUR. At this point, it would be interesting to compare both method displays. Looking forward to your results.

Yes, pitch is 44, thanks for higlighting. I’ve never seen it in the light of the velocity, but your math looks to confirm my pitch is reasonable.

Interesting, but I’m lost here. Why freerunning at 18,000 bring a max output power a 9,000? I would explain why efficiency decrease, but I cannot see why. Would you elaborate it?

Unfortunately I do not have any way to measure rpm at the moment. I understand that the only way is to get a new very expensive ESC. Or there is some easiest way?

Yes, it is a point, I also think I have some cavitation. I put a camera inside the bin and I can see bubbles. Maybe it is not clear from a single frame, but I see bubbles although I cannot exclude they are coming from the water turbulence on the water surface.
image

You are using 4x4s for the lipo ? What capacity? Because 60a down to 3,7v/cell with a 4s 10A for exemple gives a 6C , my pack was discharging at 3c and i couldn’t enough power at this end
Motor or lipo get hot at the end tests?

Oh, I assumed your diagonal was from head of W1 to head of W2, like from mounting point to mounting point of the string.
But then ok, having such a low angle will cancel out the effect you get from the pulley design.

Every BDLC motor has technically the maximum power at 1/2 * n0 (freespin RPM) or in other words at 1/2 M0 (starting torque). Just look it up, the formula is super simple, power is proportional to n (RPM) * M (torque), at 0 RPM you get high torque but thus 0RPM also 0 power, and at max RPM you get 0 torque, so power is also 0.
For max power you got to find the extremum which is at 1/2 of the dependend inputs.
image
RPM (blue), Current (red), Efficiency (green) and power (yellow) over Torque on bottom axis

And as you can see, efficiency is quite bad at the max power, thats why you might want a max. 6kW motor to do a 2-3kW job (except weight or volume is critical).

Your efficiency obviously also follows the graph above. It has to decrease since more (motor) amps means more torque for BLDC motors, so you will move to the right in the diagram.

Every ESC with telemetry can tell you the RPM (since they have to track it to commutate in the right moment) so the flier has a pc connector? Maybe the software can give you some output?

Or you can try some stuff like:

But I am not so sure how good it works with non combustion engines.

Still you should be able to just record the sound and have a look at the audio file e.g. via audacity. Android devices should sample with 44kHz, your signal is <350Hz, so you should look for a repetitiv patter with more than 125 sample points and measure the time interval between. Maybe you can even extract the pattern from the audio spur of your gopro.

3 Likes

i was thinking more about this kind of graph, this is for 350kv and taking 3nm of torque for a max power to equal the max output amp of this kind of motor : around 130A

so i don’t understand the 9000rpm @Giga?

max rpm 45000, stall current around 1600A…

yours is the same as mine, just zoomed in, blue is rpm?!
Your graph starts at ~19kRPM and stops at ~17kRPM, bring it down to 0RPM and it looks exactly the same. Just different axis scaling and zoomed in.

1 Like